• Tüm Kategoriler
    • SparkFun Wake on Shake

      SparkFun Wake on Shake
      SparkFun Wake on Shake
      SparkFun Wake on Shake
      SparkFun Wake on Shake
      Görsel 1
      Görsel 2
      Görsel 3
      Görsel 4
      DomiPuan : 165
      Fiyat:
      24,95 USD + KDV
      İndirimli Fiyat (%15) :
      21,21 USD + KDV
      Kazancınız 3,74 USD
      KDV Dahil:
      195,27 TL
      195.27 www.domirobot.com
      Aynı Gün Kargo





      Description:
       Have you ever wanted your project to just “hibernate” until someone picks it up or moves it? It’s a great strategy for dramatically extending the battery life of a widget that doesn’t need to be active all the time. The SparkFun Wake-on-Shake board is designed to make it really simple to do just that!

      The Wake-on-Shake, based on a concept by Nitzan Gadish of Analog Devices, combines the ATTiny2313A with the ADXL362 low-power MEMS accelerometer to cut power to your project for long periods of time, all the while waiting for a shake or a bump and sipping < 2uA @ 3.7V! With power consumption that low, the limiting factor for lifespan in most devices will be aging-related self-discharge of the batteries.

      The board is easy to use, you basically connect it as a power switch between your device and a power source (2.0-5.5V). By default, the board will activate the load when it experiences a mild bump or tilt; the load will be powered for 5 seconds after that. Using a serial data connection, the sensitivity can be increased or decreased, as can the delay time. Additionally, the “WAKE” pin allows the load to control when it goes back to sleep. By pulling the wake signal high (to at least 2.7V), the load will remain energized until it releases the pin.

      Note: While it is possible to connect the load to the on-board serial port, allowing the load to access the ADXL362 and EEPROM storage of the ATTiny2313A, caution must be exercised when doing this to avoid sourcing current to the load through the serial port data lines on the ATTiny2313A, which could damage the ATTiny2313A as well as causing excessive off-state power dissipation.

       

      Features:

      • Supply Voltage: 2.0 - 5.5VDC
      • Power Consumption in Hibernation: < 2uA @ 3.7V
      • Wake Signal: 2.7 - 15V
      • Serial Header for Configuration is FTDI Basic Breakout Compatible
      • ISP Header for ATTiny2313A is Broken Out, No Bootloader is Available
      • 2mm JST Connector for LiPo Battery Input
       

      Documents:



       
      Diğer Özellikler
      Stok KoduSPA-SEN11447
      MarkaSparkfun
      Stok DurumuVar
      Kutu A-204


      Bizi Takip Edin DomiRobot Müşteri Hizmetleri Hızlı Erişim  
      Twitter Hakkımızda Ödeme Seçenekleri Anasayfa  
            


       
      Facebook İletişim Bilgileri Kargo/Teslimat Hakkında Yeni Ürünler
      YouTube Banka Hesapları Kullanım Şartları İndirimdekiler
      Telegram  DomiPuan Sistemi Gizlilik Politikası Sepetim
          Üye Giriş/Yeni Üye İade ve Garanti Şartları Download
               
        

      PlatinMarket® E-Ticaret Sistemi İle Hazırlanmıştır.