• Tüm Kategoriler
    • SparkFun BlackBoard

      SparkFun BlackBoard
      SparkFun BlackBoard
      SparkFun BlackBoard
      SparkFun BlackBoard
      Görsel 1
      Görsel 2
      Görsel 3
      Görsel 4
      DomiPuan : 170
      Fiyat:
      23,00 USD + KDV
      KDV Dahil:
      201,16 TL
      3.0 2
      201.16 www.domirobot.com
      24,34 TL'den başlayan taksit seçenekleri için tıklayın.
      Aynı Gün Kargo Sınırlı Sayıda
      SparkFun' tarafından üretilen BlackBoard, bir Arduino Uno'da ihtiyacınız olan her şeye sahiptir.

      BlackBoard, bildiğiniz ve sevdiğiniz tüm donanımsal çevre birimlerine sahiptir: 14 PWM pini, 4 Analog Giriş, UART ve SPI ile handful of external interrupt pins bulunan 14 adet dijital I / O pini. 

      3.3V regülatörünü, tam termal ve ters devre korumasıyla 600mA'ya kadar çıkarmak için yükseltilmiş ve ADC okumalarının hassasiyetini arttırmak için fazladan ayırma kapasitesi eklenmiş. Sürekli büyüyen I2C tabanlı Qwiic ürünlerimize hızlı ve sorunsuz bağlantı sağlamak için, pano kenarına 3.3V voltaj çevirisi ve Qwiic konektör eklenmiş.

      Özellikler:
       
      • ATmega328P microcontroller with Optiboot (UNO) Bootloader
      • CH340G USB to Serial IC
      • Reinforced microB connector
      • Built-in Qwiic connection
      • Input voltage: 7-15V
      • 0-5V outputs with 3.3V compatible inputs
      • 14 Digital I/O Pins (6 PWM outputs)
      • 6 Analog Inputs
      • ISP Header
      • 32k Flash Memory
      • 16MHz Clock Speed
      • Flat bottom, all SMD construction


      Dökümanlar:

       
      • Schematic
      • Eagle Files
      • Drivers: The CH340G uses CDC drivers built in to most modern OS including Windows 7, 8, 10, Linux Mint, OSX Yosemite, El Capitan, and Sierra which means you shouldn’t need to install any extra software. However, there are a wide range of operating systems out there, so, if you run into driver problems, you can get drivers here.
        • Windows - Driver version 3.4 (2016-09-28)
        • Linux - Driver version 1.5 (2018-03-18)
        • Mac - Driver version 1.4 (2017-01-11) for 10.9, 10.10, 10.11, and 10.12
      • Arduino IDE Download
      • Please visit the BlackBoard repo for the latest design files

      ------------------------------------------------------------------
       

      The BlackBoard from SparkFun is everything you need in an Arduino Uno with many extra perks. BlackBoard has all of the hardware peripherals you know and love: 14 Digital I/O pins with 6 PWM pins, 4 Analog Inputs, UART, and SPI with a handful of external interrupt pins. BlackBoard even has an SMD ISP header to connect SPI pins to shields.

      We’ve applied every lesson we’ve learned about making a better Uno and created the BlackBoard. The USB to serial is now done with the ubiquitous CH340G requiring fewer driver installs and a rock solid microB connector with through hole anchoring. The power portion of the BlackBoard has been reworked: we upgraded the 3.3V regulator to provide up to 600mA, with full thermal and reverse circuit protection, and added extra decoupling capacitance to increase the sensitivity of the ADC readings. We’ve decreased the brightness of the power LED, pin 13 LED, and the TX/RX LEDs from blinding to just perfect. We’ve added 3.3V voltage translation and a Qwiic connector to the edge of the board to allow for quick and seamless connection to our ever-growing line of I2C based Qwiicproducts.

      And for more advanced users we’ve added an I/O jumper. Cut the trace to 5V and solder a jumper to the 3.3V side and the board will run at 3.3V. This is extremely handy if you have a shield or 3.3V sensitive devices, such as an SPI interface, that needs protecting.

      The SparkFun BlackBoard comes fully tested with the Optiboot bootloader and can be easily programmed with the ‘Arduino/Genuino Uno’ option from within Arduino. You can power the BlackBoard over USB or through the barrel jack. The on-board power regulator can handle anything from 7 to 15VDC. Check out the related items below for a compatible wall-wart power supply.

      Not sure which Arduino or Arduino-compatible board is right for you? Check out our Arduino Buying Guide!

      A4/A5 Pins: We recommend you don't use A4/A5 for analog to digital conversion. The Qwiic connector is wired to the I2C pins on the BlackBoard. This means A4 and A5 have external 2.2k pull up resistors and will affect readings if you use them as analog to digital conversion pins. A0 through A3 still work fine as ADC pins.
      Diğer Özellikler
      Stok KoduSPA-SPX14669
      MarkaSparkfun
      Stok DurumuVar

      İlginizi Çekebilecek Diğer Ürünler



      Bizi Takip Edin DomiRobot Müşteri Hizmetleri Hızlı Erişim  
      Twitter Hakkımızda Ödeme Seçenekleri Anasayfa  
            


       
      Facebook İletişim Bilgileri Kargo/Teslimat Hakkında Yeni Ürünler
      YouTube Banka Hesapları Kullanım Şartları İndirimdekiler
      Telegram  DomiPuan Sistemi Gizlilik Politikası Sepetim
          Üye Giriş/Yeni Üye İade ve Garanti Şartları Download
               
        

      PlatinMarket® E-Ticaret Sistemi İle Hazırlanmıştır.